KAD/ADC/120 12 channel Full-bridge ADC
Download Product Sheet register now
12 channel, Full-bridge ADC (voltage excitation, 3kHz b/w) - 12ch at 12ksps
The KAD/ADC/120 is used to condition and digitize up to twelve D/E analog channels.
At the heart of the KAD/ADC/120 is a hard-wired state-machine that over-samples all channels at a rate between 48 ksps and 96 ksps and digitally filters any noise above the user-programmable cutoff frequency.
This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth IIR filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs/4).
All signals are sampled simultaneously. Thus, when several channels are sampled at different sampling rates, at the start of an acquisition cycle all channels are aligned.
The KAD/ADC/120 is similar to the KAD/ADC/118 but does not support channel balancing. The KAD/ADC/120 is available with three different input ranges (±10V, ±1V, ±100mV). The input range must be specified when ordering.
- Downloads
- SPECIFICATIONS
- SUPPORT
- REQUEST A QUOTE
Product Downloads
Featured Downloads
- TEC-NOT-016 - Power dissipation, an example
- TEC-NOT-019 - An Introduction to Digital Filtering
- TEC-NOT-049 - Power estimation
- TEC-NOT-001 - Strain gages and ideal bridges
- Manual: DAS Studio 3 User Manual
- Environmental Qualifications Handbook
- KAM-500 Databook
- KSM-500 Databook
- Aerospace Instrumentation Brochure
Features
- 112 full or ½-bridge, potentiometer or differential ended input channels
- Ordering Input range (±100mV, ±1V, ±10V)
- High accuracy (max. 0.12% FSR at unity gain)
- Programmable voltage excitation per group of three channels
- High impedance (>10MΩ/50kΩ) when on/off
- Shorts only affect channels sharing excitation
- 16-bit simultaneous sampling on each channel
- Up to 12K samples per second per channel
- Up to 3kHz Bandwidth (AAAF filter)
Applications
- Analog signal Acquisition
- Differential Ended
- Full Bridge
- Half Bridge
- Potentiometer
DAS Studio 3 Setup software for DAUs, network switches, recorders and ground stations
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
KAD/ADC/135 12 channel Full/½-bridge ADC
The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...
KAD/ADC/136 8 channel Flexible ADC
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
KAD/DSI/102 24 channel Digital Module
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
KAD/MAT/101 Microcontroller-based module
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
KAD/VID/106 H.264 Video Encoder
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
KAM/CHS/03F Acra KAM-500 chassis (base-mounted power supply and housing) - 3 user-slots
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
KAM/CHS/04L Acra KAM-500 chassis, narrow form - 4 user-slots
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
NET/REC/001 Ethernet Network Recorder (CompactFlash)
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
NET/SWI/101 - Gigabit Ethernet Switch
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Product Finder
CONTACT SALES
Contact our sales team today to learn more about our products and services.
GET SUPPORT
Our support team can help answer your questions - contact us today.