KAD/TDC/102 Thermocouple ADC (reference compensation, 250 Hz b/w) - 15 channels at 1 ksps

The KAD/TDC/102 is used to condition and digitize up to fifteen thermocouple channels and three channels of module junction temperature. Each thermocouple channel can be configured separately for use with a wide range of thermocouple types.  

Together, the KAD/TDC/102 and the CON/KAD/010 connector use the preconfigured module junction temperature channels 0 and 2, to perform linearization and cold junction compensation for each thermocouple channel.  At the heart of the KAD/TDC/102 is a hard-wired state-machine that oversamples all channels at a rate up to 50 ksps and digitally filters any noise above the user-programmable cutoff frequency.  

This is achieved using cascaded, half-band, Finite-Impulse-Response (FIR) filters followed by an 8th order Butterworth Infinite-Impulse-Response (IIR) filter with a default cutoff point set at one quarter of the sampling frequency (fc = fs/4).   All signals are sampled simultaneously. When several channels are sampled at different sampling rates, at the start of an acquisition cycle, all channels are aligned.

  • Downloads
  • SPECIFICATIONS
  • SUPPORT
  • REQUEST A QUOTE

Features

  • 15 thermocouple input channels
  • ±0.5°C typical and ±1.5°C worst case accuracy for K-type and L-type thermocouple (-50 to +150°C)
  • ±1.0°C typical and ±2.5°C worst case accuracy for K-type and L-type thermocouple (outside -50 to _150°C range)
  • Junction block temperature measurement
  • Programmable thermocouple type (per module)
  • Digital reference junction compensation
  • Up to 250 Hz bandwidth
  • Up to 1,000 samples per second (sps) per channel
  • 8th order Butterworth filter with programmable cutoff frequency per channel
  • Supports grounded and isolated thermocouples
  • External, third party cold junction blocks with PT100 sensors can be used if required

Applications

  • Temperature measurements with thermocouples
Acra KAM-500 chassis - 13 user-slots (extended temperature)

KAM/CHS/13U Acra KAM-500 chassis - 13 Slots

The KAM/CHS/13U/ET is a thirteen user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a power supply module which regulates power supplies for the backplane...

NET/SWI/101 Ethernet Switch

NET/SWI/101 - Gigabit Ethernet Switch

The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...

KAD/DSI/102 Discrete input (programmable counters, time tagging) - 24 channel

KAD/DSI/102 Discrete input (programmable counters, time tagging) - 24 channel

The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...

KAD/VID/106 H.264 video encoder (analog video input) - 1 channel

KAD/VID/106 H.264 video encoder (analog video input) - 1 channel

The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...

KAD/MAT/101 Microcontroller-based module

KAD/MAT/101 Microcontroller-based module

The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...

KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps

KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps

The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...

12 channel ADC

KAD/ADC/135 Full/½-bridge ADC (voltage/current excitation, programmable analog gain, FIR/IIR, 6.25 kHz b/w) - 12ch at 25 ksps

The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...

KAM/CHS/04L Acra KAM-500 chassis, narrow form - 4 user-slots

KAM/CHS/04L Acra KAM-500 chassis, narrow form - 4 user-slots

The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit.   The backplane has four slots for...

KAM/CHS/03F Acra KAM-500 chassis (base-mounted power supply and housing) - 3 user-slots

KAM/CHS/03F Acra KAM-500 chassis (base-mounted power supply and housing) - 3 user-slots

The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit.   The backplane has three slots for...

NET/REC/001 Ethernet Network Recorder (CompactFlash)

NET/REC/001 Ethernet Network Recorder (CompactFlash)

The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system.   The NET/REC/001 can be configured via...

CONTACT SALES/SUPPORT


Products

Product Finder

Connect With Curtiss-Wright Connect With Curtiss-Wright Connect With Curtiss-Wright
Sales

CONTACT SALES

Contact our sales team today to learn more about our products and services.

YOUR LOCATION

PRODUCT INFORMATION

Support

GET SUPPORT

Our support team can help answer your questions - contact us today.

REQUEST TYPE

SELECT BY

SELECT Topic