KAD/ADC/109/QB120 ¼-bridge 120Ω ADC (current excitation, programmable analog gain, 6 kHz b/w) – 8 channels at 24 ksps
The KAD/ADC/109/QB120 provides independent excitation for up to eight channels and is intended for ¼-bridge 120Ω-strain-gage type applications. Each channel has a separate programmable amplifier, programmable filter and A/D converter.
At the heart of the KAD/ADC/109/QB120 is a hard-wired state-machine that over-samples all channels at a rate between 96 ksps and 192 ksps, and digitally filters any noise above the user-programmable cutoff frequency. This is achieved using cascaded, half-band, decimate by 2, 15 tap, finite-impulse-response (FIR) filters with 32-bit coefficients followed by an 8th order Butterworth IIR filter with a default cutoff point set at a quarter of the sampling frequency.
The current through the gage is programmable (up to 25 mA in 6.35 µA steps) and is kept constant. As the resistance changes, the voltage across the gage (and hence as seen by the amplifier) changes linearly.
All signals are sampled simultaneously. This means that even when several channels are sampled at different sampling rates, the sample at the start of the acquisition will always be synchronized.
- REQUEST A QUOTE
- TEC-NOT-016 - Power dissipation, an example
- TEC-NOT-019 - An Introduction to Digital Filtering
- TEC-NOT-049 - Power estimation
- TEC-NOT-001 - Strain gages and ideal bridges
- Manual: DAS Studio 3 User Manual
- Environmental Qualifications Handbook
- KAM-500 Databook
- KSM-500 Databook
- Aerospace Instrumentation Brochure
- Eight ¼-bridge (3-wire) input channels for ¼-bridge 120Ω strain gages
- 16-bit A/D simultaneous sampling on all channels
- High accuracy
- Programmable excitation and range per channel
- 8th order Butterworth filter with programmable cutoff frequency per channel
- Excitation shorted to ground on any channel does not affect others
- Excitation before instrumentation amplifier
- Up to 24,000 samples per second per channel
- Up to 6 kHz bandwidth
- Enhanced mechanical strength between motherboard and daughterboard
- High impedance per channel when powered off
- 120Ω ¼-bridge strain gages
Setting up data acquisition systems can take a lot of time and effort, particularly as many systems today are growing larger and larger. Managing thousands of channels of data over dozens of data...
The KAD/ADC/135 is used to condition and digitize up to 12 differential ended analog channels using simultaneous sampling 16-bit A/D for each channel. At the heart of the KAD/ADC/135 is a...
KAD/ADC/136 Flexible ADC (full/½-bridge, ICP, PT100, thermocouple, FIR/IIR, 12.5 kHz b/w) - 8 channels at 50 ksps
The KAD/ADC/136 is used to condition and digitize up to eight analog channels. Each channel can be configured for use in differential-ended or single-ended voltage measurement, ICP sensor, RTD...
The KAD/DSI/102 monitors the status (high/low) of up to 24 differential-ended discrete input channels. Each of these has an assigned programmable 32-bit counter. Additionally each of the inputs can...
The KAD/MAT/101 allows you run your own programs based on a dual core C6000DSP+ARM9 microcontroller. It provides high performance DSP functions in a widely used architecture. You can develop...
The KAD/VID/106 is an H.264 video encoder card that converts one of three composite analog video inputs, or one Y/C analog video input to digital video and compresses it. Compressed video bit-rate...
The KAM/CHS/03F is a compact three user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/008 power supply unit. The backplane has three slots for...
The KAM/CHS/04L is a compact four user-slot Acra KAM-500 chassis, which along with the housing and backplane, includes a KAM/PSU/006 power supply unit. The backplane has four slots for...
The NET/REC/001 is a stand-alone Ethernet network recorder. Incoming Ethernet frames are written to a CompactFlash card using a FAT32 file system. The NET/REC/001 can be configured via...
The NET/SWI/101 is a Gigabit Ethernet switch designed for operating in harsh environments. Each port on the NET/SWI/101 is full-duplex only and can be set for 10BASE-T, 100BASE-TX, 1000BASE-T link...
Contact our sales team today to learn more about our products and services.
Our support team can help answer your questions - contact us today.